2012 Ford Focus, 155K miles, it is leaking a decent amount of coolant when my partner drives it to work but doesn’t even leak a drop if I drive it to work. The mileage is the same but I don’t sit in traffic. Could the extra heat from sitting in traffic be opening up a pinhole sized leak in the coolant line?

Edit: Thanks to a tip from the comments when the heat is turned on it leaks. I should be able to bypass that line pretty easy.

Thanks Kolgeirr@sh.itjust.works

  • Kolgeirr@sh.itjust.works
    link
    fedilink
    arrow-up
    39
    ·
    1 year ago

    Any chance your partner uses the heater and you don’t? Many cars have a heater core bypass valve that only allows coolant into the heater core when the heat is on in the cabin.

    • YoBuckStopsHere@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      30
      ·
      1 year ago

      Thanks! I tried this, and it leaked. The issue is at the heater core. I’ll putting together a bypass to the line that is leaking now.

      • Kolgeirr@sh.itjust.works
        link
        fedilink
        arrow-up
        18
        ·
        edit-2
        1 year ago

        Awesome! I claim victory for this thread. One more notch carved into the 1/2" ratchet.

        People be jumping straight to head gaskets way too much when coolant issues arise.

      • Zero@ezekielrage.com
        link
        fedilink
        English
        arrow-up
        4
        arrow-down
        3
        ·
        1 year ago

        So you are breaking the heater in your car and removing the defroster a safety feature? Just replace the heater core…

    • P00Pchute@lemmy.world
      link
      fedilink
      arrow-up
      4
      ·
      1 year ago

      This seems like the best option. That or stop and go traffic is causing the coolant to over flow and leak out. Possible cooling fan issues if the problem is only in stop and go traffic whereas on the highway at constant speed it’s fine.

    • drewdarko@kbin.social
      link
      fedilink
      arrow-up
      2
      arrow-down
      1
      ·
      1 year ago

      Even with that design it would leak coolant. The bypass just prevents the flow of coolant but it should always be primed with coolant even when it isn’t flowing.

      • Kolgeirr@sh.itjust.works
        link
        fedilink
        arrow-up
        3
        ·
        1 year ago

        It’ll be primed but not pressurized. Some leaks, especially in older rubber hoses, only leak under pressure when the swelling of the hose opens the split.

        • drewdarko@kbin.social
          link
          fedilink
          arrow-up
          3
          ·
          1 year ago

          I’ve only seen bypass valves that block off one of the two heater core hoses to prevent flow but not both. Same idea as a thermostat blocks only one side of your radiator to prevent flow. So even though coolant isn’t flowing, it is heating up and pressurizing. There may be vehicles out there with an unusual design that blocks both inlet and outlet hoses to the heater core. But this isnt one of them.

          Not trying to argue, just trying to share some of my knowledge as a former Ford tech.

          • Kolgeirr@sh.itjust.works
            link
            fedilink
            arrow-up
            2
            ·
            1 year ago

            Huh, didn’t know that. Most of my wrenching has been done on older GM trucks and they used a vacuum actuated valve that cut the heater core out entirely by closing the loop under the hood, so coolant still flows by a shortened path. I’m just glad ops problem was found there. Thanks for the info!

            • drewdarko@kbin.social
              link
              fedilink
              arrow-up
              2
              ·
              edit-2
              1 year ago

              Ya, op got it figured out thx to you that’s the important part. I just wanted to add a little clarity for the poor bastard that will come across this post after googling “Ford Focus coolant leak”.